Індекс рубрикатора НБУВ: К222.234.77 + Ж820.5 с

Рубрики:

Сталь для трубопроводів. Трубна сталь

Технічне обслуговування. Технічне діагностування

Шифр НБУВ: Ж44086 Пошук видання у каталогах НБУВ 

Індекс рубрикатора НБУВ: К641.51-1

Рубрики:

Електродугове зварювання металів

Шифр НБУВ: Ж44086 Пошук видання у каталогах НБУВ 

Application of tubular elements in the chemical industry is widely used. The special properties of materials and their reaction to the welding thermal cycle is quite complex. This is especially true of titanium alloys, which when heated are sensitive to environmental influences, require special welding techniques and undergo residual welding deformations. The welded joints of tubular elements made of titanium alloy brand PT-7m, which undergo transverse deformations due to welding, are studied. It is necessary to ensure high-quality sealed welds. Analysis of the literature has shown that to obtain a guaranteed penetration it is necessary to increase the power of the arc discharge or perform multi-pass welding. This will provide larger cross sections of welded parts and should provide the specified strength characteristics. However, this technology, in turn, leads to an increase in residual deformation in the vicinity of the welded joint due to the intensive increase in the coefficient of linear expansion when heating the material. Also, the special thermophysical properties of titanium alloy such as increasing the affinity for gases when heated, increasing the grain size lead to a decrease in strength properties. In the presented work it is proposed to use a mechanical angular deformer with an indicator head and a reference base for the study of transverse residual deformations. Peculiarities of measuring sockets and methods of their preparation are revealed. A calculation scheme for determining the amount of deformation has been developed, which has been tested on flat welded specimens and transferred to tubular elements. The sequence of deformation measurement process is described and the peculiarities of their formation on flat samples and tubular sections are studied. The constructive decision of a welded joint of pipes which provides use of a compensation ring is offered. This approach allows to provide reliable protection of the root of the seam and its optimal formation with minimal residual deformation. At the same time it is possible to reach the reproducible form of a dagger of similar penetration in one pass. The result is a welded joint of the lock type, which is sealed and has a free formation of the seam root with high-quality protection by the gas atmosphere. The use of pulsed arc welding with a non-fusible electrode in an argon environment with filler wire allows to minimize the thermal impact on the base metal. Statistical processing of experimental data on the parameters of the welding mode and their influence on the residual transverse welding deformations is carried out. To obtain an unambiguous statistically reliable answer about the valid law of distribution of experimental data of the results of strain measurement, the balancing procedure and the development of an analytical approximation distribution model are involved. It is shown that the measured values of the residual transverse deformation of the welded assembly are correctly described by the Laplace distribution, which predicts (probability not worse than 90 %) a decrease in the average value of the deformation value by 1,3 times.

Due to their simplified spatial shape, shell cylindrical designs have acceptable manufacturability. The latter makes it possible to use a variety of fusion welding methods in their manufacture, including the option of mechanized welding in protective gas environments. Such a technological process is considered to be sufficiently developed in terms of theory and application, as evidenced by specialized equipment for it and numerous recommendations for the selection of installation and running welding parameters. Analysis of such material demonstrates that the basic technology is welding in the lower position with a seam root lining or with the use of a suitable technological arrangement for rotating large structures to provide such conditions. Much more difficult to meet the quality requirements for a welded joint are repair and welding works of non-rotating structures with a one-sided approach to the welding zone and the absence of a seam root lining. In this case, welding equipment with electric or electric-mechanical control of the process of dropwise transfer of metal into the bath is used, regardless of the spatial position of the seam. However, in cases of single production or repair welding, classical welding sources are still widely used, in which the regulatory requirements for the weld are provided by its appropriate external characteristics, the effect of self-regulation of the arc and dynamic characteristics. Here, the variant of droplet transfer with a short circuit of the droplet to the bath is typical, with the characteristic instability of energy accumulation/return of the source choke at the stages of the arc and droplet and the corresponding behavior of the arc in different spatial positions. Since the parameters of the mode are interdependent and, thus, welding itself represents a poorly organized system that has a variety of physical parameters that cause different in nature, but tightly interconnected processes in the zone of weld formation. The best tool for assessing the condition and regulation of such a system today is planning an experiment with independent controlled (setting) parameters of the welding mode and quality feedback - the optimized amount of weld penetration. On the basis of the processing of the array of recommended data regarding the selection of the value of the setting parameters of the welding process by the procedure of constructing symmetric histograms and the distribution polygon and calculating the analytical model of the description of the distribution density for each setting parameter of the process, their average values are set with a probability of 0,9. The latter were used to calculate the actual values of the following parameters for welding a given material thickness - electrode wire diameter 1,6 mm, welding current 190 A, voltage 25 +- 1 V, welding speed - 26 - 42 m/h, wire feed speed 21 - 29 m/h, electrode discharge wire 16 mm. On the basis of the specified reference base of parameter values, a planned experiment was set up and implemented to find the optimum on a matrix of a composite symmetrical three-level plan, as variable factors are set - process voltage, welding wire feed speed and welding speed; the height of penetration of the assembled parts is set by the response. The region of the optimum and the influence of the setting parameters of the mode on it, as well as the analysis of its response surfaces and cross sections of such surfaces demonstrate that the setting parameter - the source voltage should practically be constant at the level of 24 V and does not have a significant adjustment ability for the correction of the welding mode. The setting kinematic parameters of the mode are the wire feed speed and the welding speed, respectively 23 and 27 m/h, at the given arc voltage, they provide welding in one pass. In terms of the depth of the ability to adjust the quality of the seam formation, the welding speed prevails, since, all other things being equal, the wire feed speed is strictly correlated with the speed of its melting at a given diameter and electrode distance. The latter determine the actual value of the current, the value of which is limited by the source voltage, which is strictly specified and constant for the given process under study.