Пошуковий запит: (<.>I=Ж44086/2019$<.>) |
Загальна кількість знайдених документів : 3
Представлено документи з 1 до 3
|
 |
Ukrainian journal of mechanical engineering and materials science : наук. журн..- Lviv- Title.
- Contents.
- Shixaliyev K., Abbasov I., Sadig K. Rheological Properties of Melts and X-Ray Method of Study of Cross-Linked Polyethylene. - C. 1-12.
- Zelenyak V., Kolyasa L. Mathematical Modeling of the Thermoelastic State in a Circular Disk With a Crack Due to the Action of the Heat Source. - C. 13-19.
- Shоlovii Y., Maherus N. Substantiation of Geometric Parameters of Discharge Hopper Hole at Gravitational Outflow of Finely Dispersed Bulky Material. - C. 20-28.
- Kuzio I., Vasyliv B., Korendiy V., Borovets V., Podhurska V. Substantiation of the Shape of a Solid Oxide Fuel Cell Anode Using the Stress-Strain and Shape-Dependent Crack Deceleration Approaches. - C. 29-38.
- Molkov Y., Ivanyts’kyi Y., Lenkovs’kyi T., Trostianchyn A., Kulyk V., Shyshkovskyy R. Experimental Determination of Critical Strain Energy Density of Ductile Materials. - C. 39-44.
- Uvarov V., Bespalov S. Prediction Of Tribological Properties оf Structural Steels Using Artificial Neural Networks. - C. 45-60.
- Korendiy V., Zinko R., Muzychka D. Substantiation of Structure and Parameters of Pneumatic System of Mobile Robot With Orthogonal Walking Drive. - C. 61-72.
- Vorobyov M., Prokopenko D. Elements of the Theory of Closed-Loop Mechanisms Formed By Rolling Bodies Without Kinematic Sliding. - C. 73-84.
- Brytkovskyi V., Kachmar R., Lanets O. Influence of the Ignition System Parameters on the Ecological Indicators of the Automobile Gas-Fueled Engine. - C. 85-92.
- Kindratskyy B., Litvin R. Oscillation Processes in a Transmission With a Dual-Mass Flywheel While Moving a Car From Rest. - C. 93-104.
| 2019 | Vol. 5 | Num. 1
|
|
| |
Ukrainian journal of mechanical engineering and materials science : наук. журн..- Lviv- Title.
- Contents.
- Shixaliyev K., Abbasov I., Sadig K. Theory and practice of obtaining composite materials based on polymer blends. - C. 1-15.
- Savchuk P., Matrunchyk D., Kashytskyi V., Sadova O., Moroz I. The influence of metal oxide powders on the physical and mechanical properties of epoxy composites for the protection of constructions made of aluminum alloys. - C. 16-24.
- Zelenyak V., Kolyasa L. Modeling of elastic state for two joined dissimilar semi-infinite plates with crack under the action of pressure on the shores of the crack. - C. 25-32.
- Kuzio I., Vasyliv B., Korendiy V., Borovets V. Optimization of geometric parameters of a semi-spheroidal solid oxide fuel cell anode using the 3D stress and strain distribution graphs. - C. 33-42.
- Shepelenko I., Tsekhanov Y., Nemyrovskyi Y., Posvyatenko E., Eremin P. Simulation of micro-cutting in the process of finishing anti-friction non-abrasive treatment. - C. 43-52.
- Olshanskiy V., Burlaka V., Slipchenko M. Solution of the equation of force of impact of solids expressed by the Ateb-sine. - C. 53-60.
- Voytovych М., Velychko L., Lampika R., Lishchynska K. Calculation of strength of heated curvilinear bar structural elements of tubular cross-sections. - C. 61-67.
- Korendiy V., Zinko R., Cherevko Y. Structural and kinematic analysis of pantograph-type manipulator with three degrees of freedom. - C. 68-82.
| 2019 | Vol. 5 | Num. 2
|
|
| |
Ukrainian journal of mechanical engineering and materials science : наук. журн..- Lviv- Title.
- Contents.
- Molchanov V. Statement and solution of non-stationary problem of liquid filtering in a deformed porous medium. - C. 1-7.
- Andrukhiv A., Sokil B., Sokil M. Wave concept of motion in mathematical models of the dynamics of two-dimensional media studying. - C. 8-15.
- Zelenyak V., Kolyasa L., Klapchuk M. Mathematical modeling of stationary thermoelastic state in a half plane containing a periodic system of cracks due to periodic local heating by a heat flux. - C. 16-24.
- Zozulia P., Polishchuk O., Kostyuk N., Polishchuk A. Development and investigation of device for processing polymer materials by 3D-printing method. - C. 25-32.
- Trostianchyn A., Shvachko S., Kulyk V., Pleshakov E., Molkov Y., Lenkovskiy T. Microstructure and microhardness of nickel-base heat-resistant alloys obtained by directional and equilibrium crystallization. - C. 33-38.
- Trush V., Fedirko V., Luk’yanenko A., Stoev P., Tikhonovsky M., Kovtun K. Differences of the effect of thermal treatment in an oxygencontaining gas medium on properties of the surface layer Ti, Zr, Hf. - C. 39-43.
- Zakharov V., Kuzio I., Korendiy V., Dmyterko P. Analysis and improvement of design diagrams and mathematical models of vibratory lapping machines. - C. 44-56.
- Kusyi Y., Lychak O., Topilnytskyy V., Bošanský M. Development of the finishing and strengthening technological operations using SADT-technologies. - C. 57-69.
- Slipchuk A., Kuk A., Kusyi Y. Modeling of "combined cutter - cone” connection in tricone drill bits. - C. 70-76.
- Lanets O., Kachur O., Korendiy V. Classical approach to determining the natural frequency of continual subsystem of three-mass inter-resonant vibratory machine. - C. 77-87.
| 2019 | Vol. 5 | Num. 3-4
|
|
Простий
Розширений
Книжкові видання та компакт-диски
